Install umbrella pole extenders if needed.įor concrete decks or paver decks that are tightly joined and set on concrete sub deck, use the same process as described above for drilling through the pool, only it’s not as deep to drill most pool decks are about 3-4 inches thick, and most pavers only 2-3 inches thick.Using the AquaStar or Waterway Umbrella Sleeve will allow you to have a finished edge, the fluted top edge covering the hole that was drilled. Umbrella height is a personal preference, but remember that when in an 8-inch deep in-deck umbrella stand, your umbrella will be at least that much shorter overall. Experimentation can help you choose the best location(s) for in-deck pool umbrella stands. The umbrella location depends on the location of the sun, which varies by time of day, and time of season. Pool Deck Umbrella Standsįor vinyl and fiberglass pools, or anyone who doesn’t want to drill holes in their swimming pools, you can place umbrella stands in the pool deck, right up against the pool, or just off the edge of the deck, depending on your sun exposure.īefore you jump right into installation, I recommend that you use a regular umbrella stand first for a few days, or even an entire season, to be sure of the location of permanent umbrella stands in the pool deck. Don’t use PVC pipe (which can be used in pool decks), because it doesn’t have the fluted top ring that allows you to pack the plaster thick around the sleeve to keep it watertight. Use Umbrella Sleeve and Center Cap, the Waterway Umbrella Sleeve for Concrete Pools. Then pack a thick bead of plaster under the top lip of the ladder holder and over the top edge to prevent movement and leakage. Mix up a wet plaster patch material like EZ Patch and pour in a thin slurry as you push the umbrella sleeve or pipe into the hole. Once the hole has been cut through the pool shell, use a chiselto chip away 1 inch around the top of the hole, so the umbrella holder can sit slightly below the plaster level. Some pools can be extremely thick and will need a hole saw extension to continue drilling. Choose a location without rebar and drill, baby, drill! It may take a good 30-60 minutes of drilling, so let your drill (and yourself) rest every 5-10 minutes. Drain the pool (of course) and use a stud finder to find the rebar in the pool. On existing pools, buy a diamond concrete hole saw of the right size, a bit larger than the umbrella sleeve that you are using, and attach to a heavy duty rotary hammer drill. More than one sleeve can be installed for placement options or to have more than one in-pool umbrella. On new pools, the builder will typically drill out the gunite or shotcrete and place the umbrella mounts during plastering of the pool. The method used on existing pools to drill through the pool is to use a diamond-tipped hole saw on a powerful drill. Umbrella sleeves can also be added into the shallow-end floor but will require pole extenders to raise the umbrella about 4 feet above the water level. The method we are describing today is how to drill into your pool (concrete pools only) and insert an umbrella holder (sleeve) into the pool step, bench or tanning shelf. The third thing is that you should consider placement carefully to provide the shade you want during different times of the year, when the sun is higher or lower in the sky. ![]() Umbrella pole extensions can be used to raise in-pool umbrellas above eye-poking level. Another thing to keep in mind is that when a pool umbrella is in the pool, it may be lower (in height) than you imagine. When using an umbrella in the pool, especially in a salt pool, be sure to use one that is stainless steel, aluminum or fiberglass, or some other material impervious to chlorine and salts. ![]() This allows you to get shade over a portion of the pool and pool deck for more comfortable relaxation, and because it looks really cool. ![]() ![]() This post is about how to install pool umbrella holders or stands, either in the pool (for concrete pools) or in the pool deck, close to the pool edge. The purpose is obvious: to provide shade in areas of the pool and pool deck, and a cool look. The hot new trend in pool construction is in-pool umbrellas with umbrella stands built into the pool steps or benches, or built into the pool deck.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |